Machines
From manual loading to the fully automatic line: PROFIN builds the system around the process — FLAKKOTING tool, compensation control and software from a single source.
The PROFIN machine landscape
The workpiece is decisive — the machine follows from it. The batch size decides how far it is automated: from manual loading to the line.
For cutting tools, indexable inserts and contours

K2E — Key-2-Edge
The 6-axis edge centre with Vision-Control, Acoustic Emission and MIKRO-KI: Hand, Ecco, Robo, Serie. This is where FLAKKOTING and INNOFLAKK reside.
To the K2E →
FEM / FUM
Linear system with FLAKKO unit 3/2: up to 204 inserts per mask, vision, RFID, robot handling. The FUM is the little sister of the FEM.
To the FEM →
LEM / DLK / DLE
Continuous-pass system in various widths; DLK and DLE are the more compact machines of the LEM, modular in design with up to four processing stations, dynamic compensation, double-sided processing with turning module.
To the LEM →
ROBO-FLAKKO
Modular FLAKKOTING cell: up to 3 units, up to 3 high-frequency spindles, customer-specific robot gripper.
To the cell →
RTK / DRR / RUM
Rotary table transport with FLAKKO or FLAKKO-MULTI unit, up to 3 disc tools under program control.
More →
RTF
FLAKKOTING at bench-top size: loading masks, table mechanical, magnetic or vacuum.
More →RTK · DRR · RUM
Continuous rotary table transport, the parts run through the process — for deburring, surface finishing and defined edge preparation on precision components and cutting tools.
- RTK — FLAKKO-MULTI unit, rotary table with horizontal travel axis: large, heavy parts are handled outside the process chamber
- DRR — FLAKKO-MULTI unit, two independently controlled, reversible rotary table transports
- RUM — FLAKKO unit with continuous rotary table transport, as GREENLINE RUM 1-4/2 with robot cell and part pallets
- Up to 3 different disc tools in use under program control (MULTI), separated-compartment system: drive and control separated from the abrasive process

FLAKKOTING — small but perfectly formed
The bench-top machine for laboratory, small batches and process development: the same FLAKKOTING tools, the same process, on a table the size of a mask.
- Loading masks the size of the table
- Table versions mechanical, magnetic or vacuum
- Optionally with handling systems from PROFIN
From the single machine to the fully automatic line
PROFIN builds the upstream and downstream process integration individually for fully automatic lines — infeed conveyors, linking with the machines before and after.
PROFIN develops the handling for feeding and removing the workpieces itself: matched to part, cycle time and system, so that the line runs without an operator.
Discuss your line
Control, compensation, accessories

Software
Control software with database for machine, process, robot or Pick&Place — one user interface for the entire system, with fault diagnosis, statistics and integrated operating manual.

Automatic compensation
The brush wears, the control readjusts: dynamic tool compensation even with discontinuous belt loading, self-teach-in — and as a retrofit for third-party machines with feed sensor.

Yoke demagnetisers
Manufacture, sales and repair of the yoke demagnetisers (formerly Bohli Magnete, Solothurn): standard and special versions, integration into machine infeed and outfeed.
One edge, two winners
The benefit is shared. Whoever manufactures or regrinds cutting tools sells a documented edge. Whoever machines with FLAKKOTING-treated cutting tools changes tools less often, has less downtime and produces less scrap.
- One third less carbide for the same machining work at the customer: 100 cutting tools become 62.5.
- Less scrap in your own production: a defined edge instead of a jagged one, every cutting edge the same — commercially available inserts vary by 20 to 50 µm along one cutting edge.
- A sales argument with a figure: radius, K-factor and tool life documented per workpiece. The data sheet replaces the promise.
- Regrinding at new-tool level: the reground drill gets the same edge as the new one.
- +60 % tool life in the customer test, up to +100 % in the technical literature: fewer tool changes, less downtime.
- Predictable wear instead of edge fracture: the change of cutting tools can be scheduled, less scrap and rework on the component.
- Process-reliable at high cutting values: uniform surfaces without chipping marks, Ra −30 % measured in drilling.
- Less raw material per component: 37 % fewer cutting tools bought, stored, transported, disposed of.
Test your workpieces — and us
Process laboratory in Littau: you send a series, PROFIN prepares, measures and shows the process live.
Tool sample processing
You send us your workpiece, we treat it by FLAKKOTING in the process laboratory in Littau and you receive the measured results: radius, K-factor and images of the edge. First results from approx. CHF 800, FLAKKOTING day with documentation on request.
